camshafts

英 [ˈkæmʃɑːfts] 美 [ˈkæmˌʃæfts]

n.  凸轮轴
camshaft的复数



柯林斯词典

  1. 凸轮轴
    A camshaft is a rod in an engine and works to change circular motion into motion up and down or from side to side.

    双语例句

    1. Distribution: two overhead camshafts, 16 valves.
      分布:两个顶置凸轮轴,16气门。
    2. The camshafts are hollow providing an oil passage for a better lubrication.
      凸轮轴是空心提供一个更好的润滑一油路。
    3. Camshafts installed removing and installing camshafts-engine removed.
      已安装凸轮轴拆卸和安装凸轮轴发动机已拆下。
    4. Lay the completely preassembled unit, camshafts with chain and tensioning element into the cylinder head.
      将完整的预装配单元(带传动链和张紧元件的凸轮轴)放到气缸盖中。
    5. Be careful of the rocker arms and hydraulic tappets when removing the camshafts.
      拆卸凸轮轴时,要小心摇臂和液压挺杆。
    6. Insert the camshafts into the camshaft housing.
      将凸轮轴插入到凸轮轴室中。
    7. Loosen camshaft controllers and sprockets on the four camshafts BY2 turns.
      将四个凸轮轴上的凸轮轴控制器和链轮松开两圈。
    8. Never apply forces across the camshafts in the timing drive mechanism.
      切勿对正时传动机构中的凸轮轴施力。
    9. Intake and exhaust camshafts driven via dual chain by the crankshaft.
      进气凸轮轴和排气凸轮轴由曲轴通过双链驱动。
    10. Only turn engine using the crankshaft pulley, not at the camshafts.
      仅能使用曲轴皮带轮转动发动机,而不是在凸轮轴处转动。
    11. Note height difference of tool and the position of the camshafts in the cylinder head.
      请注意工具的高度差异,以及气缸盖中凸轮轴的位置。
    12. Lift camshafts up and out.
      向上提出凸轮轴。
    13. Place the timing chain over the camshafts when inserting the camshafts.
      插入凸轮轴时,请将正时链条放置在凸轮轴上方。
    14. The camshafts must not be preloaded or tilted.
      不得预装或倾斜凸轮轴。
    15. When installing the camshafts, make sure the rocker arms do not slip off the valve pressure face.
      安装凸轮轴时,确保摇臂不会从气门压力面上滑下。
    16. Mark hall sender cable plugs according to position of intake and outlet camshafts.
      根据进气凸轮轴和排气凸轮轴的位置在霍尔变送器电缆插头上作标记。
    17. Pay attention to marking and allocation of camshaft adjusters to camshafts!
      注意标记和分配凸轮轴调整器!
    18. Some high-performance engines have two separate camshafts, one for each set of inlet and exhaust valves.
      一些高性能发动机有两个单独的凸轮轴,分别负责开关进气门和排气门。
    19. Install timing chain for camshafts.
      安装凸轮轴的正时链条。
    20. This play is necessary so that the camshafts can still be turned.
      此松动很有必要,这样凸轮轴仍然可以转动。
    21. Pay attention to marking and allocation of camshaft controllers to camshafts!
      注意标记和针对凸轮轴的凸轮轴控制器分配!
    22. Make sure not to confuse the connectors for the intake and outlet camshafts.
      确保没有混淆进气凸轮轴和排气凸轮轴的接头。
    23. It must be possible to insert the camshaft guide into the rear slits on the camshafts.
      必须能够将凸轮轴定位装置插入到凸轮轴的尾部切口中。
    24. Remove timing chain between intermediate shaft and camshafts.
      拆下中间轴和凸轮轴之间的正时链条。
    25. Pull guide rails between the camshafts away from the threaded pegs.
      将凸轮轴间的导轨拉离螺纹销钉。
    26. Now all four camshafts are fitted uniformly and without play with both staking tools.
      现在,已使用两个锁紧工具均匀地安装了全部四个凸轮轴,且不存在间隙。
    27. Remove camshafts on both cylinder banks.
      拆卸两个气缸组上的凸轮轴。
    28. Cylinder sleeves, camshafts and piston pins can be coated with the new method.
      新涂层工艺适用于汽缸套,凸轮轴和活塞销。
    29. Processing camshafts by the technique of high-speed-and-precision grinding can meet our satisfaction for high speed, efficiency and precision.
      采用高速精密磨削方法和工艺加工凸轮轴可以满足高速、高效、高精度的加工要求。
    30. Learning and knows no studies beyond servo-systems and distributors, compression ratios and camshafts.
      这些人对学习毫无兴趣,而且除了伺服系统,配电盘,压缩比和凸轮轴便一无所知。