chamfer

noun

1. 斜切面；削角
   a cut made along an edge or on a corner so that it slopes rather than being at 90˚

1. This paper analyzes the lack of traditional settingout method and the advantage of digitalization settingout method when analyzing settingout of chamfer stake in cubic meter of earth and stone.
   分析了土石方工程中坡口桩放样时，传统放样方法的不足和数字化放样方法的优点。
2. Select those front edges and chamfer them then click apply and chamfer it again but this time with a lower value.
   选择前面的边并倒角，然后单击应用并以较低的值再次倒角。
3. Chamfer ends of all screw threads
   将所有螺丝端部斜切
4. RECHAMFER: Defect on radii and chamfer; defective chamfer such as nicks that are considered to be repairable.
   重新倒角：可被重新修复的倒角缺陷，例如划痕。
5. The effects of rolling parameters such as plate width, roll contours, chamfer and straight chamfer parameters on the contact pressure distribution were studied.
   研究结果表明，在轧制能力范围内，轧件越宽，轧辊采用凹辊型可以使辊身部的辊间压力分布更为均匀；
6. Optional accessories are: to plug, referral chamfer, outlet.
   可选配件有：地插座、下线槽、出线口。
7. CHAMFER: The flat surface formed by cutting away the sharp edges of two meeting surfaces.
   倒角：两个表面相交处，通过切掉尖锐边缘形成的平面。
8. Drag onto the page. Right-click to set chamfer angle.
   拖到绘图页上。右击可设置切角角度。
9. The specialized inspector inspects the bore diameter, pitch, chamfer and finish degree of bore wall.
   加工完成后由专门检验员检验孔径、孔距、倒角大小、孔壁光洁度。
10. But for Reminder: the dimensions related to big chamfer are not major characteristic.
    但提醒：大倒角的尺寸并不大特点。
11. Core drills. A core drill consists of the chamfer, body, neck, and shank, as shown in Fig.12.2.
    空心钻包括斜面、钻头体、钻颈和钻柄，如图12.2所示。
12. Single type angle drills: Use to machine chamfer for hole of glass, stones etc. Various type and specification.
    独立倒角钻头：用于玻璃孔、石材孔倒角使用。各种型号及规格。
13. In order to miniaturize the millimeter wave circuit system, this study improved the traditional chain SIW filter and brought forward a new type of compact configuration with chamfer angle.
    为了实现毫米波电路系统小型化，对传统链式SIW滤波器进行改进，提出了一种新型的带倒角的紧缩结构SIW滤波器。
14. If you need the capability study on the big chamfer for300 pcs, then we have to measure at CMM ( 3D) as GFT method.
    如果您需要300个大倒角能力的研究，那么我们在三坐标测量机（3D）测量GFT的方法。
15. What is the nominal chamfer size?
    什么是公称倒角尺寸？
16. Conclusion: Amalgam post and core technique is conservative in restoring molars for its curved root canal, big root furcation and large pulp chamfer.
    结论：对于根管弯曲、叉大、室大或C型根管的磨牙，银汞桩核修复效果良好。
17. Also, the chamfer of the stay vanes entrance and the surface roughness of the flow channel were optimized by the numerical investigations.
    亦对固定导叶入口冲角、涡壳壁面粗糙度对流动的影响进行了定量分析。
18. Programming Method of Milling of Chamfer and Fillet Based on$ TC_DP
    基于＄TCDP铣削斜面及倒圆角的程序编制方法
19. Based on physical simulation of edge rolling process in Trimming-Free Plate rolling method, the affection of V rolling and chamfer rolling on the plate profile is analyzed.
    基于中厚板无切边轧制法中立轧轧边变形的物理模拟，分析了平辊立轧与倒棱轧制对中厚板断面形状的影响。
20. Carefully remove smaller edges or burrs on the chamfer of the crankshaft flange with an oilstone if necessary.
    如有必要，请用油石仔细去除曲轴法兰倒棱上的小边或毛刺。
21. Drag to add perpendicular lines with adjustable chamfer size.
    拖动此形状，可添加切角可调的垂直线。
22. Or just the dimensions related to big chamfer?
    或者只是尺寸大倒角？
23. Making drilling by using numerical control drilling machine and ensuring the dimensions of horizontal direction and vertical direction of holes and chamfer through accuracy of the drilling machine.
    数控铣削：对尖轨前端工作边及贴合面的加工时采用大型数控龙门铣床加工，通过专用夹具、专用刀具和对应的数控程序保证尖轨前端各个断面的尺寸和形貌。
24. Rolling bearing chamfer dimension limits
    GB/T274-1991滚动轴承装配倒角极限
25. In addition, this paper compares this technology with gear chamfer technology of grinding wheels and finds the advantages of flexibility abrasive deburring technology.
    并与砂轮齿轮倒角技术进行了对比，总结出了柔性研磨回转体去毛刺技术的优点。
26. After too large tooth resultant force is eliminated, tooth chamfer bone is OK proper motion rehabilitate, of the tooth become loose degree also return to normal subsequently;
    当过大的牙合力消除后，牙槽骨可以自行修复，牙齿的松动度也随之恢复正常；
27. The control strategy based on constant force will result in an uneven chamfer for its characteristics in nature.
    控制策略的基础上不断的部队将结果在粗糙的槽的特点大自然。
28. Fit the sealing ring at the correct position in the vacuum pump so that it is flush with the lower edge of the chamfer in the rotor.
    将密封圈安装在真空泵的正确位置，以便密封圈与转子倒棱的下边缘平齐。
29. The Study and Realization of Auto Marking Chamfer and Taper in UG
    倒角和锥度自动标注在UG中的研究和实现
30. Marking chamfer and taper is a routine work in Mechanical drawing.
    在机械制图中，通常需要进行大量的倒角和锥度的标注工作。

noun

1. two surfaces meeting at an angle different from 90 degrees

   Synonym:    bevelcant

verb

1. cut a furrow into a columns

   Synonym:    furrowchase

2. cut a bevel on
   1. bevel the surface

   Synonym:    bevel