crankshaft

noun

1. 曲轴；曲柄轴
   a long straight piece of metal in a vehicle that connects the engine to the wheels and helps turn the engine's power into movement

1. N-COUNT (内燃机的)曲轴，曲柄轴
   A crankshaft is the main shaft of an internal combustion engine.
   1. The engine had a broken crankshaft.
      发动机的曲轴断了。

1. The engine had a broken crankshaft.
   发动机的曲轴断了。
2. The camshaft rotates in phase with the crankshaft, but at half its speed.
   凸轮轴和曲轴协调旋转，但速度仅是曲轴的一半。
3. A new type testing machine, the adaptive resonant crankshaft fatigue bending machine, is developed.
   研制了一种新型试验装置&自适应共振式曲轴弯曲疲劳试验机。
4. The timing is controlled by the camshaft which is synchronized to the crankshaft by a chain or belt.
   凸轮轴通过皮带链接与机轴保持同步，准确控制了可燃气体的进出时间。
5. Only turn the engine on the crankshaft and never on the camshaft as the timing chain can jump over.
   只能在曲轴上（不得在凸轮轴上）转动发动机，否则正时链条可能会跳起来。
6. Intake and exhaust camshafts driven via dual chain by the crankshaft.
   进气凸轮轴和排气凸轮轴由曲轴通过双链驱动。
7. Never turn the engine at the crankshaft without guide and tensioning rails.
   没有导轨和张紧轨时，请勿转动曲轴上的发动机。
8. The drop-forged crankshaft runs in five bearings and has eight counterweights.
   落锻曲轴具有五个轴承和八个配重。
9. The nationalization of engine crankshaft blank for Jetta, Bora and Golf car was realized.
   实现了捷达、来和高尔夫轿车发动机曲轴毛坯的国产化。
10. In automobile engines, all pistons are attached to a single crankshaft.
    汽车发动机活塞，所有连接到一个单一的曲轴。
11. Only turn engine using the crankshaft pulley, not at the camshafts.
    仅能使用曲轴皮带轮转动发动机，而不是在凸轮轴处转动。
12. Crankshaft and connecting rods are new, and made out of very high strength steel.
    曲轴，连杆是新的，并提出了非常高强度钢。
13. Put on chain between crankshaft drive sprocket and intermediate shaft drive sprocket.
    安装曲轴传动链轮和中间轴传动链轮之间的链条。
14. Abstract: The article introduced a grinding method and principle of the journal of crankshaft connecting rod.
    本文简述了一种正在兴起的曲轴连杆轴颈的磨削方法和原理。
15. If the limit of wear is equalled or exceeded, replace the crankshaft and bearing shells.
    如果等于或超过磨损极限，请更换曲轴和轴瓦。
16. Fit the crankshaft belt pulley with a helper.
    与一个助手装配曲轴皮带轮。
17. The stroke of an engine piston moving toward the crankshaft.
    蒸汽机或其他发动机中活塞向曲轴推动的冲程。
18. Always turn the engine at the crankshaft and at the camshaft.
    始终在曲轴和凸轮轴处转动发动机。
19. In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.
    在发动机里，机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上。
20. The paper further develops and enriches the methods of ICE single order fault diagnosis in angular vibration of crankshaft.
    论文的研究工作，进一步发展和丰富了内燃机单谐次曲轴角振动故障诊断方法；
21. It can also be applied to one crank and one-piece crankshaft of one cylinder or multicylinder engine.
    该方法速度快捷、精度高，适用于单缸机和多缸机的单拐曲柄和整体曲轴。
22. The metal case enclosing the crankshaft and associated parts in a reciprocating engine.
    曲柄轴箱在往复式发动机内将曲柄轴和相关部件包住的金属箱子。
23. Oil pump drive chain sprocket is pressed onto the front of the crankshaft.
    油泵驱动链轮上按下了曲轴的前面。
24. The nitrite chrome-molybdenum steel crankshaft guarantees the best tensile strength and surface hardness for long-time operation.
    亚硝酸盐铬钼钢曲轴保证了最佳的拉伸强度和表面的长期运作的硬度。
25. Remove vibration damper bolt and washer from end of crankshaft.
    从曲轴端拆下减震器螺栓和垫圈。
26. CKP sensor rotor plate is fitted to crankshaft counterweight No.1 by pin and screws.
    转子板的CKP传感器安装在曲轴销和螺钉重第一。
27. The study of torsional vibration and bending and axial vibration of crankshaft system are summarized in this paper.
    简单综述了内燃机曲轴扭振、弯振和纵振的研究内容及相关方法。
28. A new structure for fixing the bearing bush of the connecting lever in a crankshaft press is introduced.
    针对曲轴压力机连杆上轴瓦的固定问题，介绍了一种新的固定结构。
29. The camshaft and crankshaft gears can be connected directly, or meshed.
    凸轮轴和曲轴齿轮可能被直接连结，或者相啮合。
30. Clean crankshaft flange and crankcase bore carefully.
    小心地清洁曲轴法兰和曲轴箱孔。

noun

1. a rotating shaft driven by (or driving) a crank