push-out
英 [pʊʃ aʊt]
美 [pʊʃ aʊt]
网络 推出; 推出试验; 微推出; 顶出试验; 顶出
双语例句
- It mainly includes a hydraulic pressure main engine, a stripping power supply, a male die, two female die composite units together with a lining board and a parison push-out mechanism.
主要包括液压主机、脱模电源、阳模、连同衬板在内的两个阴模组合体、型坯顶出机构。 - Simulation analysis of push-out test based on ANSYS software
基于ANSYS的栓钉推出试验仿真分析 - Large Protein Production Through Split Intein-Mediated Trans-Splicing Push-out experimental study on shear connectors in embedded composite beams with notched web
通过断裂内含肽介导的反式剪接合成大的蛋白腹板嵌入式组合梁中抗剪连接件推出试验 - The bond-slip tests were carried out on 20 push-out specimens, 20 steel reinforced concrete columns in eccentric compression, and 23 steel-high strength concrete columns under horizontal repeated and reversed loading.
进行了20个型钢混凝土构件的推出试验、20根型钢混凝土偏心受压柱试验，以及23根型钢高强混凝土柱在反复荷载作用下的试验。 - Study of Interfacial Shear Strength on Fine Weave Pierced Carbon/ Carbon Composite by Push-out Test
顶出法对细编穿刺碳/碳复合材料界面强度的研究 - The bond strength between bone and titanium coatings was also measured by push-out test.
涂层与骨组织之间的结合强度用推出实验进行测量。 - Based on the experimental results of 2 push-out specimens and 8 steel reinforced concrete beam specimens, the affections of bond state, number of stirrups and shear connectors to the mechanical behavior of steel reinforced concrete beams are analyzed.
本文基于2个压出试件和8根型钢混凝土梁试件的试验结果，分析了型钢和混凝土之间的粘结状态、箍筋间距、剪力连接件对型钢混凝土梁破坏模式以及力学性能的影响； - In order to analysis the performance of stud shear connectors in composite Steel-FDPCP ( full-depth precast concrete panels) beams, twelve push-out specimens of different hole mold and different material filled in holes have been conducted.
为了研究钢-混凝土预制板组合梁中栓钉剪力连接件的性能，对不同的预留孔型、孔内不同的填充材料等12个推出试件进行试验研究。 - Moreover, P-s curves are analyzed according to the results of push-out test.
此外结合六组推出试验的测量结果，分析了推出试验的P-s曲线及其受力特征。 - Based on the test of 6 push-out and beam specimens, some analytical model about bond behavior between shape steel and concrete is developed in the paper, on the other hand, the comparison between test results and theoretical study is also presented in the thesis.
本文基于6个压出试件和6个梁式试件的试验结果，建立了型钢与混凝土之间粘结的一些分析模型，并对理论分析和试验结果进行了比较。 - In the process of push-out, each piers is not only bearing the erect pressure, but also the horizontal thrust.
而在顶推过程中，各墩除承受竖向压力外，还承受水平推力的作用。 - Methods ① Biomechanics: the MPC or calcium phosphate cement ( CPC) was implanted into the intercondylar region of bilateral femurs in 36 rabbits, then the push-out tests were made at 1, 2, 3, 4, 6, 8 weeks after the procedure.
方法①生物力学部分：双侧股骨髁上钻孔后，分别植入MPC和磷酸钙骨水泥（CPC），术后分别饲养1、2、3、4、6和8周后取出股骨下段作推出试验。 - Using the bond slip constitutive relation curve achieved from push-out experiment, nonlinear finite element analysis for some specimens is carried out, and mechanical behaviors under different bond conditions of steel reinforced concrete beams are analyzed.
利用压出试验所确定的粘结滑移本构关系曲线，对型钢混凝土梁进行非线性有限元模拟，分析型钢混凝土梁不同粘结条件下的受力性能。 - The calculated results are shown to agree with experimental data of push-out tests.
验算结果表明，本文公式与试验结果符合良好。 - The result of the push-out test can be normally used to work as the basis of bearing capacity design, but carrying out test need to spend a lot of money and time, and the test requires a higher experimental condition.
国际上通常采用推出试验结果作为承载力设计的依据，但采用推出试验方法需要耗费大量资金和时间，且对试验条件要求较高。 - The official push-out of Chinese GEM in 2009 was considered as another important milestone in the development process of Chinese capital market.
2009年中国创业板市场的正式推出，是中国资本市场发展历程中又一重要的里程碑。 - After 1(?) 3(?) 6 months of operation, specimens were harvested and assessed by means of gross observation, X-ray examination, scanning electron microscope observation, histological observation, push-out test and uniaxial pull-out test of implants.
术后1、3、6个月取材，进行大体标本观察、X线检查、扫描电镜观察、组织学检查及种植体的推入实验和拉出实验。 - Through push-out test, the force characteristics, load-slippage rule, failure mechanism of single shear stud in joint section are studied, the shear capacity and shearing stiffness of single shear stud are calculated.
通过推出试验，研究分析了推出试件中单枚剪力钉的受力特性、荷载-滑移规律和破坏机理，计算分析了单枚剪力钉的抗剪承载力及剪切刚度。 - A total of 24 push-out specimens are tested to failure.
总共24件推出试验样本用来进行了破坏试验。 - The research method can be used to carry out the push-out testing and finite element simulation analysis.
其研究方法可采用推出试验和有限元计算仿真分析。