sprockets

英 [ˈsprɒkɪts] 美 [ˈsprɑkəts]

n.  链轮; 输片齿轮; 链轮齿; 链齿
sprocket的复数



柯林斯词典

  1. 链轮;(胶片的)输片齿轮;(磁带的)带齿卷盘
    A sprocket is a wheel with teeth around the outer edge that fit into the holes in a chain or a length of film or tape in order to move it round.

    双语例句

    1. The contact surfaces of the outlet sprockets and camshaft flanges must be completely free of oil and grease.
      排气链轮和凸轮轴法兰的接触面必须完全没有机油和润滑脂。
    2. Remove the chain sprockets of the camshafts.
      拆卸凸轮轴的链轮。
    3. The new folder, on the other hand, is for 32 sprockets slated for production and delivery in the next quarter.
      另一方面,新文件夹是有关下个季度生产和交付32个齿轮件的合同。
    4. Loosen camshaft controllers and sprockets on the four camshafts BY2 turns.
      将四个凸轮轴上的凸轮轴控制器和链轮松开两圈。
    5. The belts have a light weight single layer construction and are positively driven by sprockets.
      乙型网带具有单层结构,较轻,使用链轮驱动。
    6. If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets.
      若正时链不令人满意,则拆下凸轮轴链轮固定螺栓,并拆下曲轴和凸轮轴链轮的正时链。
    7. I'll have to leave the gear sprockets for assembly later this week.
      我得把齿轮、链轮留到本周晚些时候再装配。
    8. In addition, improvements in lubricating mechanism, brakes, and chain and sprockets were made.
      另外,还在润滑、刹车、链轮链条的选用等方面作了一些改进。
    9. These must match the corresponding markings on the sprockets or camshaft adjusters.
      这些标记与链轮或凸轮轴调节器上的相应标记相对应。
    10. Some movement of sprockets and timing marks as belt tension is adjusted is normal.
      当调整皮带张力时,链轮与正时记号有些许移动是正常的。
    11. These help the fitter during initial assembly in the workshop and must match the corresponding markings on the sprockets and camshaft adjusters.
      这些链节会在车间的初始装配期间对修理工人起帮助作用,并且必须与链轮和凸轮轴调整器上的相应标记匹配。
    12. Kinematic Analysis and Parameter Optimization of Eccentric Sprockets Transmission Mechanism
      偏心链轮传动机构的运动学分析及参数优化
    13. This kind of method can reduce the number of cutters and mades a diversification on designing schemes of tooth shaped chains and involute sprockets.
      这种方法可以减少刀具数量,使齿形链和渐开线链轮的设计方案多样化。
    14. At the same time the crank main shaft delivers the power to conveying system by double little sprockets which with the same ratio.
      同时,切割器曲柄主轴经一对同比小链轮将动力传递给输送系统;
    15. Structure analysis and parameter optimization of SEPARATING-PLANTING mechanism with eccentric sprockets for high-efficiency transplanter
      双季稻高速插秧机偏心链轮分插机构结构设计和参数优化
    16. Conveying system adopt two leather belts, using horizontal conveying to deliver the input power of cutting system to the main shaft through the two same ratio sprockets.
      输送系统采用上、下两根皮带,横向输送,将切割系统输入功率通过曲柄主轴上小链轮同比传递给输送主轴。
    17. The study on the associated impact between rollers and sprockets and dynamic loading in the system is carried out with different motion laws.
      对其在不同运动规律下链与链轮的啮合冲击、链节张力及附加动载荷等进行了分析与研究。
    18. 2-D drawings of involutes sprockets and machined process were given in the software of involutes sprockets.
      渐开线链轮CAD软件给出了传动用齿形链各种节距下的渐开线链轮的二维图形以及加工仿真过程。
    19. The machine is the transmission system with motor as power that transmits drive through gear reducer, sprockets, and uses the rod on big sprocket that makes the focus of partial ship moving upwardly.
      输送带煤流采样机是以电机为动力,通过减速器及链轮传递驱动力,利用大链轮上的挡杆使偏心轮重心上移的传动系统。
    20. Here, we investigate the mechanical properties and wear resistance of warm-compacted P/ M materials, and the developed warm-compacted P/ M engine sprockets.
      在这种情况下,我们研究了温压粉末冶金材料的力学性能与耐磨性,并开发出了温压粉末冶金发动机链轮。
    21. A mathematical model indicating an engagement between practical chains and hobbed sprockets is built.
      本文以滚子链传动为例,建立了实际链条与实际滚切链轮相啮合的数学模型;
    22. The mechanism is driven by hydraulic motor and the power is transferred via sprockets and chain.
      该传动机构采用链条与链轮啮合传动,由液压马达驱动。
    23. CAD and Machining Simulation of Involute Sprockets
      渐开线链轮CAD与加工仿真
    24. Because of the low meshing impact on the silent chain, involutes sprockets were widely used on the silent chain mechanism. However, the design and manufacture of involutes sprockets were studied by few domestic researchers.
      渐开线齿形链轮因与链条啮合时冲击小而应用于很多齿形链机构上,但是国内很少有人研究这种链轮的设计制造过程。
    25. Profile Design of Shaper Cutters for Cutting Sprockets
      链轮插齿刀齿形设计
    26. Through the kinematic and dynamic analysis on the mechanism, it is found that the variations of speed, acceleration and dynamic tension of the chain while meshing with sprockets are closely related to three parameters: chain speed, chain pitch and tooth numbers of the sprockets.
      对该传动装置进行了运动学和动力学分析,认为链条在与链轮啮合时的速度、加速度及动态张力的变化都与链条的速度、节距、链轮的齿数这3个参数有密切的关系。
    27. Therefore, drive smoothness can be enhanced by increasing chain speed, decreasing chain pitch and properly increasing tooth numbers of the sprockets to decrease or eliminate dynamic meshing loads and reduce drive speed variation.
      因此通过增大链条的运行速度、减小链条的节距、并适当增大链轮的齿数,减少和消除了啮合时的动载荷、减小运行的速度变化、提高了传动的平稳性。
    28. The dual meshing silent chain mechanism is designed, which comprises the dual meshing silent chain and new kind of sprockets.
      研究了新型链轮的齿形修正方法,设计了可与双面啮合链条配合的新型链轮齿形。
    29. Profile Modification and Dynamic Simulation of Sprockets with Silent Chain
      齿形链链轮齿形的修正与动力学仿真
    30. The engagement of tooth shaped chains and involute tooth formed sprockets
      齿形链和渐开线齿形链轮的啮合设计