wear-out
英 [weə(r) aʊt]
美 [wer aʊt]
n. 磨损；消耗；用坏（旧，完）
双语例句
- This minimizes the risk of "wear-out" that is common to less advanced Flash devices.
这可以减小低端闪存设备常见的“磨损”风险。 - With the friction curve and wear scar diameter analysis, it can be found that the carrying capacity of reaction product is lower, which makes it easy to wear-out in the experiments.
依据摩擦曲线形态特征以及磨斑直径的相对关系，可以发现醇在氮化硅陶瓷表面摩擦时所产生化学反应膜的承载能力较弱并较易在摩擦过程中去除。 - The work roll application situation in plate mill in China is analyzed, and the roll wear-out failure phenomena which is more serious than advanced countries is pointed out.
通过分析我国中厚板轧机工作辊的使用情况，指出其辊耗和国外工业先进国家的差距。 - Investigation on Edge Wear-Out of Abrasive Wheel during Creep-Feed Grinding of Deep Groove
缓进给磨削深直沟槽时砂轮边角磨损的试验研究 - Study on wear-out failure of fiber reinforced aluminosilicate glass ceramics
纤维增强铝硅酸盐玻璃陶瓷磨损失效机理研究 - Cause Analysis of the Idler Gear Wear-out in the Three-roll Compact Device
三罗拉集聚装置中过桥齿轮易磨损原因分析 - ATTENTION: Make a mark on your order if Tire Protection chains will be used on wear-out tires.
注意：装甲链如要装在已磨损轮胎上，请在合同中注明。 - Causes of CCU Main Air Distributing Duct Wear-out and the Preventives
催化裂化装置主风分布管磨损原因及改进措施 - This solution enables the frame to be used for millions of times without any abrasion or wear-out.
这种方法能达到模框连续冲压数百万次无磨损的特点。 - If a component survived the'infant mortality period,'it would follow a predetermined'bath tub curve,'until it reached a wear-out point, which was when the parts were serviced.
飞机附件先是经过初装使用阶段，然后即按照一个预定的“浴盆曲线”到达它的磨损点之后换掉，其实在到达磨损点时部件仍然可用。 - The failure type and wear-out mechanism of the linings was analyzed based on investigation of wear failure forms of the liners.
通过考察衬板的实际工况和磨损失效形式，分析了衬板的磨损失效类型及其机理。 - Research on Time-domain Characteristics of Spindle Motor Power Signals during Milling Cutter's Progressive Wear-out
立铣刀渐进磨损过程中主电机功率信号的时域特性研究 - The wear-out of plane tyres is serious and should be replaced periodically.
由于飞机轮胎磨损快，要求经常更换。 - Analysis of Cutting Force and Wear Area during the Wear-Out of a Milling Cutter
铣刀磨损过程中铣削力与磨损面积分析 - Cam Wear-out and Remedy
凸轮轴凸轮的磨损与修复 - This article introduces the braking mechanism and main specifications of the brake and the automatic adjustment of wear-out clearance between the friction lining and brake disk.
阐述液压盘式制动器的制动原理和关键参数设计，并介绍摩擦片与制动盘在使用中磨损间隙的自动调整。 - The wear-out and anti-wear design of En-masse conveyor components
埋刮板输送机零部件的磨损失效与防磨设计 - Based on the gradually appeared failure model of wear-out failure, an extended test method is developed with the help of the stable wear stage theory.
根据耗损失效产品的渐发性故障模型，应用稳定磨损阶段的理论，提出了一种延拓试验方法。 - The concept of reliability of function for crankshaft-connecting rod system is discussed, and the wear-out factors which make system function lost are analysed.
讨论了曲柄连杆机构运动功能可靠性的概念，并分析了造成该机构运动功能丧失的各种磨损因素。 - Fetter Fuel Filtration Quality Less Plunger Mates Wear-out
提高燃油滤清器过滤精度减少柱塞偶件的磨损 - Discussion on the countermeasures of reducing roll wear-out failure of plate mill
降低中厚板轧机辊耗对策的探讨 - The results show that step-down-stress ALT method can improve testing efficiency remarkably when applied in wear-out life evaluation.
研究结论表明，步降应力加速寿命试验方法应用于与耗损型失效对应的长寿命评估可以大幅度提高试验效率，而不影响加速寿命试验的评估精度。 - The wear-out monitor is developed by using this character.
铁粒子最大的特点是具有可磁化的性质。 - The routine method of calculating tool path uses the ideal profile of cutter. The manufacturing variation and wear-out of the cutter profile can influence the machining accuracy.
传统的刀具轨迹计算方法是利用刀具的理想廓形进行的，但是刀具的廓形制造误差和磨损误差会影响加工精度。 - This thesis considers the wear-out process of the system as the sum of an additive compound nonhomogeneous poisson shock wear-out and a continuous routine wear-out in time t. With the introduction of the concept of random resource, a wear-out model is built.
本文在分析系统的磨损时，综合考虑了到达过程为非齐次泊松过程的随机冲击磨损和连续累积的常规磨损。结合随机资源的概念，建立了一个磨损模型。 - A system at inception is endowed with a random amount of resource, the process of the lapse of system life can be viewed as that of the depletion of random resource caused by the wear-out effect.
系统在初始状态时可以认为被赋予了随机大小的资源，那么系统寿命的消逝过程可以看成是磨损对随机资源的消耗过程。