The skin of her leg was abraded by the sharp rocks. 她腿上的皮肤被锐利的岩石擦伤了。
Fiber producers have reduced pilling by lowering the tenacity of their fibers so that pills May be more easily abraded from the surface of cloth. 纤维制造厂通过降低纤维的强度来减少起球,这样,摩擦生成的纤维球就可能更容易地从织物表面脱落。
The difficulty in NC grinding is that the size of the work piece cannot be invariable because the grinding wheel will be abraded continuously in the grinding process. 数控磨削加工的难点在于,由于砂轮在磨削过程中是不断磨损的,因此使得被磨工件的加工尺寸不能恒定。
After one set of teeth is abraded, the tooth-plate can be reversed so that the other set of teeth can be used, and therefore, the service life of the tooth-plate is increased. 当一组牙齿磨损后,可掉过头来使用另一组牙齿,从而提高了牙板的使用寿命。
An abraded area where the skin is torn or worn off. 皮肤脱落的磨损地区。
It is occasionally applied to abraded surfaces with good results, especially if there is some rusting due to a delay in painting after blasting. 这种方式常常被使用在磨擦过的金属表面,特别是那些在喷沙后因没有及时油漆而产生锈蚀的金属表面,并产生非常好的效果。
Pills formed from synthetic fibers of high breaking strength remain on the surface because they are too strong and tough to be abraded away. 由高强度的全成纤维生成的纤维球会一直粘附在织物的表面,这是因为纤维的强度过高以至于不会因摩擦而掉落。
Aircraft engines and helicopter Rotor-Blades are constantly abraded by atmospheric dust, and a way of slowing down this abrasion would be welcome. 飞机引擎和直升机的螺旋桨叶会不停地被空气中的沙尘磨损,减慢这种磨损的方法会大有用武之地。
If tractive must be too slow, will make the arrest bat batch abraded to burn eclipse but forfeit braking action. 如果拉得太慢,会使制动盘磨损烧蚀而失去制动作用。
After abraded by weaving simulator, yarn hairiness could evaluate the weavability of the sizing yarn. 对单纱精确上浆装置上浆后的浆纱经过织造模拟后毛羽变化的规律进行了研究。
Checked in the center of the abraded area not at the edge of it. 检查试片时,必须检查试片在磨擦范围中央的破坏,而不是检查其边。
The pen head of the xyloid handwriting pen for screen pen can be changed after being abraded, is convenient for the user to use, and avoids wasting; 本实用新型所述的屏幕输入用木质手写笔的笔头可以在磨损后进行更换,方便用户使用,避免浪费;
Although they are very dirty and abraded, the tertials are rather broadly white-tipped. 虽然此鸟羽毛很脏且磨损,三级飞羽还是有颇宽的白色翼尖。
To meet the requirements of new assembly procedures of wheel sets, the wheel tyre retaining ring roller mills for locomotives were developed. Third, tread and wheel rim will be abraded. 为适应轮对新的组装工艺要求,研制了机车轮箍扣环滚压机。恢复踏面和轮缘的线型时,需要对车轮进行车削修整,导致轮箍与轮缘变薄。
It provides a reference for selecting method of repairing abraded shafts. 这为磨损轴类零件的修复方法的选用提供了借鉴意义。
Painful from having the skin abraded. 因皮肤被摩擦而感到疼痛。
Stale smoky air hung in the study with the smell of drab abraded leather of its chairs. 工作室里空气浑浊,烟雾弥漫,同几把椅子那磨损咸淡褐色的皮革气味混在一起。
When the upright cutter blades are abraded and shortened, the upright cutter blades can be justified again through distance adjusting clamp holes for improving efficiency. 当立刀片磨短后,通过调距卡孔有两次调齐,以提高效率。
There's no abraded tissue to account for that. 这里没有磨损的组织来证明这个。
Because of the films being abraded during polishing, the corrosion rate was quickened and the corrosion current density was increased greatly. 抛光过程中因钝化膜被磨损,腐蚀加快,腐蚀电流密度大幅增加。
The freshly abraded specimen must then be washed in industrial spirit and Analar acetone. 然后,研磨好的新鲜试样必须在工业酒精及纯丙酮中洗涤。
Whether difficult or easy the passive films were abraded depended on the properties of the films, the polishing pressures and rotational velocities. 钝化膜的磨损难易程度与钝化膜的本身特性、抛光压力及转速有关。
The environment down there breeds bacteria and encourages them to enter abraded skin. 减少细菌生长的环境,并避免它们进入磨损的皮肤。
Helicopter grade leading-edge tape is replaceable if abraded by fine debris or sand. 直升机级的优质胶带如果被沙或其它残骸损坏可以替换。
Secondly, Classified inorganic materials have been crushed and abraded to make a lot of powder and store them separately. 第二步,将分类后的原料按一定的设计要求进行粉碎与研磨并分门别类加以储存。
When the shoe is continually abraded until the inner layer comes out, a new sole then appears. 当鞋子一直磨一直磨,磨到内层的地方的时候,就又会变出一个新的鞋底。
Dermabrasion, is a type of plastic surgery that is meant to refinish your skin by replacing the abraded skin with new collagen and epidermis. 磨削,这是一类是整形修补磨损皮肤代替你的皮肤与新胶原蛋白和表皮。
Using SEM, the abraded surface of two kinds of liner plates and one paddle have been investigated. 使用SEM电镜,对两种材质的衬板及一种材质的叶浆头的磨损面进行了观察分析。
In this paper we tried to repair the abraded shafts using laser overlaying welding technology. 采用激光堆焊技术及自动送粉工艺进行了轴件修复实验。