camshaft

noun

1. 凸轮轴
   a long straight piece of metal with a cam on it joining parts of machinery, especially in a vehicle

1. 凸轮轴
   A camshaft is a rod in an engine and works to change circular motion into motion up and down or from side to side.

1. Since the engine has no valves, it doesn't need any camshaft, valve lifters and so on.
   因为发动机没有阀门，它不需要任何凸轮轴、起阀器等。
2. But a camshaft driven directly by the crankshaft gear turns in the opposite direction.
   但是凸轮轴被曲轴齿轮直接驱动，其将在相反方向上转动。
3. The front timing cover and and a finished camshaft with timing gear on the end.
   前面的时间和范围，并完成与凸轮轴齿轮的时间就结束。
4. The contact surfaces of the outlet sprockets and camshaft flanges must be completely free of oil and grease.
   排气链轮和凸轮轴法兰的接触面必须完全没有机油和润滑脂。
5. This means that the crankshaft will make two revolutions for every revolution of the camshaft.
   这意味着凸轮轴每旋转一次曲轴将旋转两次。
6. Camshaft from the crankshaft through the timing belt or gear or chain drive.
   凸轮轴由曲轴通过齿形带或齿轮或链条驱动。
7. The camshaft rotates in phase with the crankshaft, but at half its speed.
   凸轮轴和曲轴协调旋转，但速度仅是曲轴的一半。
8. Refer to tools and tightening torques in chapter "removing camshaft housing"!
   参阅章节“拆卸凸轮轴室”中的工具和拧紧力矩！
9. Camshaft gear and servomotor
   凸轮轴传动机构和伺服电机
10. Tighten central screws on the sprocket and camshaft controller to the prescribed final torque using a torque angle wrench.
    用扭力角度扳手将链轮和凸轮轴控制器上的中央螺钉拧紧至规定的最终力矩。
11. Remove camshaft sprocket and chain tensioner.
    拆下凸轮轴链轮和链条张紧器。
12. The timing is controlled by the camshaft which is synchronized to the crankshaft by a chain or belt.
    凸轮轴通过皮带链接与机轴保持同步，准确控制了可燃气体的进出时间。
13. Insert the camshafts into the camshaft housing.
    将凸轮轴插入到凸轮轴室中。
14. Only turn the engine on the crankshaft and never on the camshaft as the timing chain can jump over.
    只能在曲轴上（不得在凸轮轴上）转动发动机，否则正时链条可能会跳起来。
15. Loosen camshaft controllers and sprockets on the four camshafts BY2 turns.
    将四个凸轮轴上的凸轮轴控制器和链轮松开两圈。
16. Fit turbocharger holder on camshaft housing.
    将涡轮增压器支架安装到凸轮轴室上。
17. A mechanical single-vane pump driven by the camshaft is used for this reason.
    为此，采用了由凸轮轴驱动的机械式单叶片泵。
18. The value-opening mechanism includes a valve lifter and a cam on a camshaft.
    一套气门开启机构包括一个气门挺杆和一个在凸轮轴上的凸轮。
19. Install camshaft actuator lid with a new o-ring.
    安装带有新o形圈的凸轮轴执行器盖。
20. Insert a self-tapping screw into the drilled pin and carefully pull the pin from the camshaft.
    插入自动攻丝螺丝到钻孔的销中，小心地在凸轮轴中拉动销。
21. Fit the short guide rails between the camshaft timing gears.
    安装凸轮轴正时齿轮之间的短导轨。
22. It drives the camshaft roller-type chain and the oil pump via a sprocket.
    它通过链轮驱动凸轮轴滚柱型链条和机油泵。
23. Replace the diamond friction washer when removing the camshaft controller.
    请在拆下凸轮轴控制器时更换菱形摩擦垫圈。
24. Always turn the engine at the crankshaft and at the camshaft.
    始终在曲轴和凸轮轴处转动发动机。
25. Design and Research of Engine Variable Valve Timing Camshaft
    对发动机可变气门正时凸轮轴的设计与研究
26. In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.
    在发动机里，机油被供应到旋转在其支承轴内的曲轴和凸轮轴轴颈上。
27. It consists of the primary roller-type chain and the camshaft roller-type chain.
    它由主滚柱型链条和凸轮轴滚柱型链条组成。
28. After working on the camshaft wheels, the timings must be set.
    用了凸轮轴车轮后，必须设置正时。
29. The camshaft and crankshaft gears can be connected directly, or meshed.
    凸轮轴和曲轴齿轮可能被直接连结，或者相啮合。
30. A camshaft driven by a chain or belt turns in the same direction as the crankshaft.
    凸轮轴被链或者带驱动，使其朝着曲轴相同的方向转动。

noun

1. has cams attached to it