clamping

英 [ˈklæmpɪŋ] 美 [ˈklæmpɪŋ]

v.  (用夹具)夹紧，夹住，固定; 紧紧抓住; 紧夹住; 被抓住; 被夹紧; 用夹锁锁住(车)
clamp的现在分词

现在分词：clamping

计算机

BNC.43220 / COCA.42307

柯林斯词典

  1. 夹子;夹具;夹钳
    A clamp is a device that holds two things firmly together.
    1. VERB (用夹具)夹紧，夹住，固定
      When you clamp one thing to another, you fasten the two things together with a clamp.
      1. Somebody forgot to bring along the U-bolts to clamp the microphones to the pole.
        有人忘了带把麦克风固定在支架上的U形螺栓。
    2. VERB 将…固定(在某处)；紧紧抓住
      To clamp something in a particular place means to put it or hold it there firmly and tightly.
      1. Simon finished dialing and clamped the phone to his ear...
        西蒙拨完号，把听筒贴在耳边。
      2. He clamped his lips together...
        他紧闭双唇。
      3. You beg him to try just one spoonful, and he clamps his mouth shut...
        你求他就尝一匙，可他就是不张嘴。
      4. Peter jumped to his feet with his hand clamped to his neck.
        彼得一只手捂着脖子，腾地跳了起来。
    3. (将违章停放的车辆扣在原地的)夹钳，车轮固定夹
      A clamp is a large metal device which is fitted to the wheel of an illegally parked car or other vehicle in order to prevent it from being driven away. The driver has to pay to have the clamp removed.

        1. in AM, use 美国英语用 Denver boot

      1. VERB 给(车辆)上夹钳
        To clamp a car means to fit a clamp to one of its wheels so that it cannot be driven away.
        1. Courts in Scotland have ruled it illegal to clamp a car parked on private ground and then to demand a fine.
          苏格兰法院裁定，将停在私人地界上的车辆上夹钳并索要罚款的行为是违法的。

        2. in AM, use 美国英语用 boot

      点击展开全文

      双语例句

      1. Press off clamping washers with a suitable tool, remove shield and shield cover with rivet bolt.
        用合适的工具压出夹紧垫圈，并拆下罩和带铆钉螺栓的屏蔽罩。
      2. Analysis of Positioning and Clamping for Workpiece in Machining Center
        工件在加工中心上的定位与夹紧分析
      3. Thirdly, how to obtain the alterable clamping force was studied.
        研究了求解变夹紧力的优化方法。
      4. The clamping schemes of thin-walled package were discussed on the base of FEM analysis.
        采用有限元分析方法，对薄壁件的装夹方案进行了讨论。
      5. And tube clamps clamping, then check with soap and water before use without leakage.
        并用管夹夹紧，然后用肥皂水检查确认无漏气方可使用。
      6. Mechanical shaft clamping via single taper mechanism, hydraulically actuated, including tailstock support.
        通过液压系统操纵锥体，连同尾架支承将工件机械夹紧。
      7. The clamping force control and the ratio control is the most important parts of the CVT control technology.
        夹紧力控制与速比控制是CVT控制问题中最为重要的两个方面。
      8. In jig design most important link is the clamping and the detent mechanism.
        夹具设计中最重要的部分就是夹紧和定位机构。
      9. The structure of the shearing die, running on common use press, with radial clamping for round bar was introduced.
        介绍了一种用在通用冲床上的径向夹紧圆钢剪切模的结构、工作原理和设计制造要点。
      10. The multifunctional inflatable boat is composed of PVC net clamping cloth, floating fillings and partial air.
        多用充气船的气囊由PVC夹网布、漂浮填充物和部分空气组成。
      11. Hydraulic hob mandrel clamping.
        液压滚心轴夹紧。
      12. It may require clamping and some minor machining.
        它可能需要的夹紧和一些小的加工。
      13. The clamping nut is fixed into a housing together with the bearing.
        夹紧架与轴承一起固定在电机的外壳里。
      14. The turret has Curvic coupling for high positioning accuracy and the hydraulic clamping for heavy cutting.
        该刀塔具有Curvic耦合高定位精度和液压夹紧为重切削。
      15. It is possible that there is a clamping cylinder damage problem or simply a plug in the lines.
        它可能是有一个夹紧缸损坏问题，还是只是一个插头的线路。
      16. Simple, safe and reliable operation, high efficiency insertion and automatic controlled clamping and contraposition.
        操作简单，安全可靠，植入效率高并能自动控制夹紧、对中。
      17. The principle and its requirements of angle dividing and clamping equipment for bolted sphere nodes are put forward.
        提出螺栓节点球分度夹紧装置原理及要求，介绍了分度、夹紧控制系统。
      18. Drilling, milling and tapping can be finished clamping one time.
        一次装夹可以完成钻孔，铣削，攻丝等加工工序；
      19. Relay IC3 opens, protecting the amplifier and clamping diodes.
        继电器IC3断开，保护放大器和钳位二极管。
      20. It is improved clamping device with involute cam, in order to carry out two-way clamping of the workpiece.
        对渐开线凸轮夹紧机构进行了改进，使其能够对工件进行双向夹紧。
      21. In this paper, an effective solution-flexible clamping is introduced for grinding this kind of part.
        文中介绍了该类零件加工中一种行之有效的解决方案&柔性装夹。
      22. The utility model provides a reliable clamping device for connection between various nonmetallic hoses and hard tubes.
        在为各种非金属软管与硬管的联接上，提供了可靠的卡具。
      23. Sealed bearing system reduces clamping pressure and increases bearing life.
        密封的轴承系统减少夹持力并增加轴承寿命。
      24. Inchworm actuators are classified by the clamping mechanism.
        按箝位方式对尺蠖驱动器进行分类。
      25. New functional construction on fly cutter drive, positioning clamping and support.
        飞刀的传动、定位夹紧及支撑采用了一系列新型的功能性结构。
      26. The key of processing tenuous hole by plain lathe is the design of clamping apparatus.
        用普通车床加工细长孔，夹具和钻具的设计是关键。
      27. The corresponding position of the other supporting hook is provided with locking clamping pieces.
        另一托钩上相应位置设有锁定卡件；
      28. A convenient method to calculate the minimum clamping force for milling process was presented.
        提出了一种计算铣削加工中夹紧工件所需最小夹紧力的简洁方法。
      29. The eccentric wheel clamping can be disassembled under the condition that the surface is rusted.
        偏心轮夹紧，在表面锈蚀条件下仍可拆卸。
      点击展开全文

      考试分类

      行业分类

      柯林斯词典词频分级词汇

      其他分类