pawl

1. Pawl is a simple device which allows a shaft to turn only one way.
   掣爪是一种非常简单的只让转轴往一个方向转动的装置。
2. If the cup plug is missing, the park pawl anchor shaft can move out of position under certain conditions.
   如果该杯状固定塞脱落，驻车止动爪定位销可能在特定情况下滑移出正常位置。
3. The middle column and the projections present an eccentric shape correspondingly to the center of the fixed pawl body.
   中柱与凸块相对于掣动杆体中心呈偏心状；
4. Tyre-lock chain interlocking pawl ( winding) wheel
   胎锁链（轮胎防滑）大钢轮，互锁棘爪轮
5. A bracket will be installed within the transmissions to assure that the park pawl shaft remains properly in position.
   在变速器内安装保持架来确保驻车止动爪定位销处在正常位置。
6. The pipe tongs is mainly composed of a fixed jaw, a movable jaw, a racket wheel, a spring, a pawl, a movable pin and a connecting pin;
   主要由固定钳口、活动钳口、棘轮、弹簧、棘爪、活动销和连接销等组成。
7. Move the feed dog up or down to perform adjustment, then securely tighten the screw. The fastening tool further includes a coil feeder ( 720) assembly having an indexing pawl ( 722).
   上下移动送布牙调节高度，然后拧紧紧固螺丝。紧固工具还包括具有分度棘爪的卷料进给组件。
8. A two-raking pawl mechanism is a kind of loading one used in a roadheader; its performance and property are unknown now.
   双耙爪是在掘进机上使用的一种装载机构，其性能和特征目前还不甚清楚。
9. The fastening tool further includes a coil feeder ( 720) assembly having an indexing pawl ( 722).
   紧固工具还包括具有分度棘爪的卷料进给组件。
10. The blades are positioned on the large handle by a rotating shaft screw, and the pushing pawl and a pawl torsion spring are connected with the small handle through the pawl pin.
    小手柄上通过棘爪销柱连接有推进棘爪及棘爪扭簧，推进棘爪受到棘爪扭簧的压力始终压制在刀片的齿上；
11. Heavy hammer on the pawl through the release of the lock device on Spindle lock spindles;
    重锤上的棘爪通过释放装置上的锁锭轴锁锭；
12. The indexing pawl advances a fastener into operative engagement with the feed pawl upon movement of the second canister portion from the open position to the closed position.
    当第二筒部从打开位置移动到关闭位置时，分度棘爪使紧固件前进并使其与进给棘爪工作啮合。
13. A toothed wheel or rack engaged with a pawl that permits it to move in only one direction.
    连接着棘爪的只能允许朝一个方向运动的齿轮或齿轮架。
14. The virtual prototype of the clutch is built based on Pro/ E and the switch process of the SSS clutch is simulated by MSC Adams. The simulation of the impact performance of the pawl and pawl wheel and the engaging performance of the middle part is finished.
    利用Pro/E及MSCADAMS建立该离合器的虚拟样机模型，并在MSCADAMS中对离合器动态接合过程进行仿真，分析棘轮棘爪的碰撞特性，以及中间件的啮合特性。
15. This control effect can be got by designing the size of pokedwheel, using the self locking character of worm wheel and worm pole and connecting the pawl mechanism with overtravel limit switch.
    通过有效设计拨轮的尺寸，利用蜗轮蜗杆的自锁特性，将棘轮机构与行程开关联为一体，达到自动输球控制的目的。
16. Simulation and Analysis of a Two-raking Pawl Loading Mechanism
    双耙爪式装载机构的模拟分析
17. Design characteristics of pawl pole permanent synchronous machine
    爪极永磁同步电机的设计特点
18. And adjusting the friction torque between the ratchet wheel and pawl can effectively increase the code discrimination performance of micro-electromechanical system code lock.
    通过控制棘轮棘爪处的摩擦力矩可有效提高微机电系统密码锁的鉴码性能。
19. Analyzing the reasons of spring failure on pressing pawl of cutting machine and heat treatment
    剪板机压料爪子弹簧失效原因分析及处理
20. This paper introduces the structure and design characteristics of pawl pole permanent synchronous machine, and illustrates the relations among main structure sizes.
    介绍爪极永磁同步电机转子的结构及设计特点，并说明了一些主要结构尺寸间的关系。
21. This paper deels with the filling density calculation and design methods to determine the num-bers of the pawl and teeth of the ratchet wheel as well as linkage lengths of the mechanism.
    本文对该机构的纬密计算，棘爪数、棘轮齿数以及传动连轩长度的确定等设计方法均作了较为详细的介绍。
22. Ratchet mechanism is often used in the reducer of the casting crane. This paper uses Pro/ ENGINEER software to create the ratchet mechanism and simulate its running and studies the stress and deformation of the ratchet wheel pawl by Pro/ MECHANICA.
    针对铸造起重机用减速器常采用的棘轮装置，采用三维实体造型软件Pro/ENGINEER建立其实体模进行运动仿真，利用Pro/MECHANICA有限元分析模块对棘爪进行应力、应变分析，得到棘爪需加强的部分。
23. The feasibility for rolling special section pawl steel with the existing& 180 mm mill at laboratory has been discussed.
    研究了用180mm轧机轧制异型断面棘爪钢的可行性。
24. The pawl type bamboo roots grab was designed.
    竹爪式竹根挖掘机方案设计。
25. The fine blanking dies of the pawl and the chute used for the seat recliner were firstly introduced in this thesis, and failure analysis has been carried out in view of mechanical calculation, metallographic test, hardness test and SEM.
    本文首先针对棘爪、滑槽板两副精冲模具出现断裂的凸模，从力学强度校核、金相试验、硬度试验、断口电镜扫描等进行试验分析。

noun

1. a hinged catch that fits into a notch of a ratchet to move a wheel forward or prevent it from moving backward

   Synonym:    detentclickdog